Shree Ram Pump & Pipe

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed to start in low voltage and sustain in high voltage fluctuations.
• High electrical and mechanical efficiency.
• Higher heat dissipation.
• Dynamically balanced rotor and other rotating parts for uniform clearance.
• Specially designed bearing to withstand axial thrust loads.
• Designed for high voltage fluctuations.
• Noise free operation.
• Modular design and all parts are easily interchangeable.
• Energy Efficient Models.
• Higher efficiency resulting in lower operating cost.
• Type of Product: Open Well Submersible Pump
• Material: Copper
• Weight: 12 Kg
• Dimension: 37 x 33 x 21 cm
• Country of Origin: India
• Colour: Multi Colour
• Generic Name: Water Pump and Motor
• Agriculture Farm
• Industries Water Supply
• Sprinkler & Drip Irrigation
• Gardens
• Residential Complex
• Hospitals
• Water Treatment Plant

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial 

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial 

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial 

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial 

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial 

LUBI Horizontal Openwell Pump – LHS

 

 

Features :

 

·  Pumpset shall be designed to withstand voltage drops to 320 volts.

·  It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·  High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·  All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·  Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·  All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·  All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial