Shree Ram Pump & Pipe

Openwell Submersible Pump sets are ideally suitable for ideally suitable for openwells or tanks where a wide fluctuation of water level occur. This works under water and rest at the bottom of the well. Prime mover is rewindable, water – cooled motor. Specially designed water lubricated bearing are used to withstand the axial thrust loads with minimum wear and tear. The stator is wound with special waterproof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure and rigidly locked. Motor sealing is made by polymers, ‘O’ rings, oil seals and sand guard to avoid ingress of well water/salt into the motor. Pressure equalizing rubber diaphragm is provided to guard the motor from pressure and volume variation of water as detailed in our operator’s manual. Three phase motor requires an adequate motor protection control panel. 

• Specially designed double side carbon pads for higher wear resistance.
• No suction and priming problem.
• Extremely tough and hard-wearing lubricated journal bearing are used.
• Dynamically balanced rotating parts ensures minimum vibration and longer life.
• Motor designed with higher cooling effect ensures longer life.
• Motor body available in SS 304 & Cast iron.
• Designed for wide voltage fluctuation.
• High operating efficiency.

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

• Products suitable for 150 mm (6.0") and above bore diameter.
• Radial Flow Pump design.
• Energy efficient Motor HP available from 3.00 HP to 30.0 HP.
• Head range Up to 400 Meters
• Motor Diameter 140 mm.
• Pump Diameter 135 mm.
• Wet type water filled design.
• Suitable for 3 Phase 440 V, 50 Hz AC power supply.

 

Materials of Construction : 

• Stator Shell : Stainless Steel
• Motor Shaft : Stainless Steel
• Motor Stainer : Copper
• Motor Winding : Copper
• Thrust Bearing : Heavy duty thrust bearing
• Motor Bush : Bronze LTB-4
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel
• Pump Shell : Stainless Steel
• Pump Shaft : Stainless Steel
• Impeller : SS 304
• Diffuser : SS 410
• Pump Stainer : Stainless Steel
• All CI Parts : Graded Casting
• All Fasteners : Stainless Steel

 

 

We offer superior quality of V-4 Submersible Pumps, which are cast from high grade stainless steel. These pumps are light and have a compact built. We use latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance. We offer superior quality V-4 Submersible Pumps which are cast from high grade stainless steel. These pumps are light and have a compact built. We use the latest technology with innovative designs in manufacturing these pumps. The outstanding quality and unbeatable performance of our product has made it our clients' favourite choice. These pumps are easy to operate, consume less energy, maintenance free, and highly efficient and on top of these, we are offering these pumps at a very attractive price. our pumps have made these extensively popular. These pumps are easy to operate, consume less energy, maintenance free and highly efficient.

This pump set is examined in terms of quality in order to supply an excellent range. Offered pump set is developed using the finest quality components and sophisticated technology. Our entire range of pump set is highly acknowledged in the market for its high quality & consistent performance. 

 

• Specially designed for 89 mm (4") and above bore Diameter
• Unique product to survive old borewell having corrosion/rusting.
• Pumps are available in Multistage, highly efficient Radial Flow design.
• Energy efficient Motor HP available from 0.50 HP to 7.5 HP.
• Head range up to 300 Meters.
• Motor Diameter 86 mm.
• Pump Diameter 86 mm.
• Wet type water filled design.
• Suitable for 1Phase 220 To 240 V, 400 To 440 Hz AC power supply with suitable control panel.

Application : 

• Domestic and Industrial water lifting (Water Supply)
• Civil and Industrial
• Fire Fighting
• Irrigation
• Fountains
• Farm houses and irrigation of small fields
• Multi-Storeyed buildings
• Water circulation systems
• Nurseries and dairies

 

 

 

LUBI Horizontal Openwell Pump (LHL) (SS + Alu.)

 

 

Features :

 

·       Pumpset shall be designed to withstand voltage drops to 320 volts.

·       It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·       High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·       All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·       Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·       All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·       All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial

 

 

LUBI Horizontal Openwell Pump (LHL) (SS + Alu.)

 

 

Features :

 

·       Pumpset shall be designed to withstand voltage drops to 320 volts.

·       It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·       High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·       All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·       Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·       All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·       All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial

 

 

LUBI Horizontal Openwell Pump (LHL) (SS + Alu.)

 

 

Features :

 

·       Pumpset shall be designed to withstand voltage drops to 320 volts.

·       It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·       High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·       All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·       Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·       All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·       All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial

 

 

LUBI Horizontal Openwell Pump – LHL 

 

 

Features :

 

·       Pumpset shall be designed to withstand voltage drops to 320 volts.

·       It has well designed sleeve and thrust bearing of adequate capacity for longer life.

·       High operating efficiencies of pumpset result into high water discharge rate and lower power bills.

·       All components are precisely machined on modern precision machine tools to give you years of reliable operation.

·       Stator and rotor of the monoset are vacuum impregnated with synthetic varnish and epoxy coated for corrosion resistance.

·       All rotating components are dynamically balanced to ensure long bearing life and vibration free smooth operation.

·       All cast iron parts shall be CED (cathode electrode deposition) coated for corrosion resistance with uniform coating and controlled deposition thickness of 20-30 microns.

 

Variety & Range

●        Flow Range : up to 310 m³/h

●        Head Range : up to 72 metres

●        Rating : 0.37 – 22 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Agriculture
• Domestic
• Industrial
• Commercial

 

 

LUBI V6 Submersible Pump – LSM / LSB

 

 

LUBI's Submersible pumpsets are made out of premium quality of raw material and workmanship to ensure that pump is energy efficient, reliable and has a very long service life with negligible repairing.

LUBI Submersibles Pumpsets are manufactured as per IS: 8034 & IS: 9283 strict quality control for year of efficient & reliable operation.

 

Material of Construction :

Motor Body   : Stainless Steel Mild Steel

Motor Stator  : Vacuum Impregnated and epoxy coated for corrosion resistance. Thick end laminations are provided to protect motor windings.

Rotor              : Vacuum impregnated, shot blasted & coated with poly urethene colour for corrosion resistance & dynamically balanced for vibration free smooth operation.

Windings        : PVC / Polyster insulated, water cooled

Journal Bearings : Leaded Bronze / Nitrile Rubber and Stainless Steel, Water Lubricated, having high load bearing capacity.

Thrust Bearings : Carbon Vs. Steel segment special self-aligning and water lubricated to withstand high axial thrust loads.

Pressure Equalizing Diaphragm :  Adequately sized to accommodate expansion of water inside the motor and prevent loss of cooling water.

Impeller          : High quality abrasion resistant Bronze / Stainless Steel & dynamically balanced.

Bowl               : High grade Cast Iron Stainless Steel Investment Casted.

Wear Rings    : High quality abrasion resistant Bronze / Nitrile Rubber

Shaft               : Stainless Steel of adequate diameter to ensure rigidity and ground to close tolerances.

Suction Casing : Provided with perforated Stainless Steel Strainer and adequately sized to allow the water to be sucked in with minimum friction.

Cable Sealing Arrangement : Designed so that no borewell water with sand can enter the motor.

 

Applications :

• Irrigation of Fields / Farms
• Community Water Supply
• Industries
• High-rise Buildings
• Housing Complexes
• Bungalows

 

 

Shallow Well Jet Pump / Centrifugal Jet Pump

 

 

Features :

 

·  The pump casing shall be fabricated from AISI 304 stainless steel sheet metal and shall have axial suction and radial discharge port.

·  The pumps shall have closed type impeller with material of construction of AISI 304 stainless steel sheet metal.

·  The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

·  The Motor will be suitable for 1 phase, 230volts, 50 Hz (Standard Supply), 3 phase, 415volts, 50 Hz.

·  All Fabricated stainless steel pump components shall be manufactured in house by the manufacturing company.

 

 

Variety & Range

●        Flow Range : up to 5.4 m³/h

●        Head Range : up to 40 metres

●        Rating : 0.37 - 0.75 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Domestic
• Industrial
• Commercial

 

 

 

Shallow Well Jet Pump / Centrifugal Jet Pump

 

 

Features :

 

·  The pump casing shall be fabricated from AISI 304 stainless steel sheet metal and shall have axial suction and radial discharge port.

·  The pumps shall have closed type impeller with material of construction of AISI 304 stainless steel sheet metal.

·  The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

·  The Motor will be suitable for 1 phase, 230volts, 50 Hz (Standard Supply), 3 phase, 415volts, 50 Hz.

·  All Fabricated stainless steel pump components shall be manufactured in house by the manufacturing company.

 

 

Variety & Range

●        Flow Range : up to 5.4 m³/h

●        Head Range : up to 40 metres

●        Rating : 0.37 - 0.75 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Domestic
• Industrial
• Commercial

 

 

 

Shallow Well Jet Pump / Centrifugal Jet Pump

 

 

Features :

 

·  The pump casing shall be fabricated from AISI 304 stainless steel sheet metal and shall have axial suction and radial discharge port.

·  The pumps shall have closed type impeller with material of construction of AISI 304 stainless steel sheet metal.

·  The Pump shaft sealing shall be by mechanical shaft seal of Carbon/Ceramic/NBR/AISI 304 construction suitable for 10 bar pressure rating and water temperature from 0 to +90 deg. C.

·  The Motor will be suitable for 1 phase, 230volts, 50 Hz (Standard Supply), 3 phase, 415volts, 50 Hz.

·  All Fabricated stainless steel pump components shall be manufactured in house by the manufacturing company.

 

 

Variety & Range

●        Flow Range : up to 5.4 m³/h

●        Head Range : up to 40 metres

●        Rating : 0.37 - 0.75 kW

●        Rated Speed : 2900 RPM

 

Applications :

• Domestic
• Industrial
• Commercial